Controlling 6063-T5 Aluminum in Cold Backward Extrusion

For its 6063-T5 aluminum cold extrusion project, TDB Hanoi is using 6063-T5 as the incoming material designation. The material condition when a blank reaches the press must be recorded separately from its incoming certificate.

Reliable process development requires more than checking whether a blank can be pressed into the desired shape. Material history, surface treatment, tooling condition, machine settings, and inspection results must be considered together.

6063-T5 aluminum cold extrusion: understand the incoming temper

6063 identifies the aluminum alloy. T5 identifies its temper: the material has been cooled from an elevated-temperature shaping process and then artificially aged.

The complete alloy and temper designation matters because material behavior depends on both composition and processing history.

Incoming material identification alone does not describe every operation performed before cold extrusion.

If an intermediate annealing treatment is used, the resulting condition must be recorded and verified. If the material is formed directly from the incoming T5 condition, trials must validate that specific route.

Why temper matters

Different tempers of the same alloy can have different mechanical properties. Hydro’s 6063 data, for example, show differences in yield strength and elongation between T4 and T5 under the stated product conditions.

Published values should not be treated as universal acceptance limits for every blank. Incoming inspection criteria must match the purchase specification, material certificate, product form, and validated process.

Applying calcium aluminate and lubricant does not replace verification of the material condition.

Building a useful trial record

Category Suggested information
Blank Batch number, dimensions, mass, certificate, and inspection results
Preparation Any heat-treatment history, coating batch, and lubricant identification
Equipment and tooling Machine identification, tooling revision, stroke, and speed settings
Forming behavior Recorded load or pressure, stripping behavior, and abnormalities
Product quality Drawing dimensions, wall and bottom thickness, and surface condition
Batch results Quantity inspected, nonconforming quantity, and defect categories

Where the machine displays hydraulic pressure, that reading should be distinguished from forming force. Conversion requires the equipment’s relevant hydraulic characteristics and verification.

Investigating common problems

The following table provides starting points for investigation. It does not establish the cause of a particular defect.

Observation Factors to investigate
Longitudinal scratches Aluminum pickup, tool surface condition, contamination, and lubrication
Cracks at the rim or body Material condition, existing defects, deformation severity, and tooling geometry
Uneven wall thickness Alignment, blank variation, equipment stiffness, and material flow
Difficult stripping Surface condition, geometry, stripping mechanism, lubrication, and temperature
Unexpected load increase Blank changes, treatment variation, settings, temperature, and tooling condition

Retain representative samples and link them to the production record. Changing several variables at once makes the results harder to interpret.

Validate continuous operation

Research on aluminum cold extrusion shows that production rate and temperature can influence frictional conditions. A slow, isolated trial may therefore behave differently from continuous production.

A validation plan should include checks during startup and later stages of the run. Sampling frequency should reflect the product risks and observed process behavior.

Verify the finished component

Incoming 6063-T5 certification does not, by itself, establish every property of the finished component after substantial cold deformation or subsequent heat treatment.

Final requirements must be verified through the agreed inspection and testing plan.

For TDB’s production teams, the working principle is to record the actual conditions, measure the required characteristics, and use evidence to identify the causes of variation.

Link the material record to the formed part

A practical 6063-T5 aluminum cold extrusion record follows the batch through blank preparation, any intermediate heat treatment and forming. If two trial batches behave differently, first establish whether they entered the press in the same documented condition. A common incoming designation does not demonstrate identical preparation history.

Keep the required finished-part condition separate as well. State which drawing characteristics will be measured after forming, which require verification after later operations and which material properties require specific testing. This avoids treating an incoming certificate as approval of a substantially changed component.

The lubrication trial checklist addresses film and tool-interface observations. The TDB aluminum cold extrusion case study describes the development project. For a component review, send TDB the drawing and material requirements and agree the trial and inspection scope.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top